The 2008 Dodge Viper defines brute power. Equipped with an 8.4-liter, 10-cylinder engine, the 2008 Dodge Viper is capable of producing over 600 horsepower. The Viper is often considered primitive when compared to ultra-luxurious supercars from Europe. However, what the Viper lacks in plush trim and options, it makes up for with its track credentials.

K&N’s Performance Air Intake System, number 69-2527TTK, for the 2008 Dodge Viper 8.4-liter V10

69-2527TTR installed on 2008 Dodge Viper 8.4-liter V10

69-2527TTR gained 18.69 horsepower for the 2008 Viper
The 2008 Viper is reported to accelerate from 0-60 mph in 3.7 seconds, cover the quarter mile in 11.8 seconds, and reach top speeds of around 200 mph. Combine that level of sheer power with the ability to precisely maneuver through turns, stop from 60-0 mph in around 100 feet, and the 2008 Viper will leave a venomous taste in mouths of European supercar owners.

K&N engineers are always hunting for more power. After looking under the 2008 Viper’s hood, K&N engineers knew the Viper was capable of more. Much consideration was put into the design of part number 69-2527TTR.

The stock 2008 Viper intake tract uses a dual throttle body set up fed by a common plenum with a single air filter. K&N intake 69-2527TTR replaces the stock pieces with twin powder coated mandrel-bent aluminum intake tubes and dual K&N high-flow air filters for improved air delivery.

This performance air intake system incorporates a unique heat shield, and the dual air filters line up with the factory fresh air intake on the hood. The result of this hard work and enthusiasm for performance is a nearly 19 horsepower gain at the wheels.

K&N’s Research and Development Department tested a 2008 Dodge Viper 8.4-liter V10 on our in-house dynamometer. Results showed horsepower increases throughout the RPM range with a shocking peak horsepower gain of 18.69 horsepower @ 5,300 RPM! 69-2527TTR provides improved performance with attractive red powder coated aluminum intake tubes to match the 2008 Viper’s valve covers.

K&N 63-3073 air intake system for 2008 and 2009 Corvette with a 6.2 liter V8 engine

The Chevrolet Corvette’s performance is legendary among enthusiasts and general consumers alike. As America’s premier sports coupe, the Corvette rivals cars that cost four times as much. This makes the Corvette an excellent buy, offering a lot of bang for the buck. A K&N air intake system is also legendary for offering an outstanding level of performance for the money. Offering a guaranteed horsepower gain, K&N’s air intake systems will make it seem like you have a different car.

K&N’s 63-3073 for the 2008 and 2009 Corvette with a 6.2 liter V8 engine provides an incredible 17 horsepower increase at the rear wheels. K&N’s Research and Development Department tested a 2008 Chevrolet Corvette with a 6.2 liter V8 engine on our in-house dynamometer. Results showed an increase across the RPM range with a dramatic peak horsepower gain of 17.72 horsepower @ 4,750 RPM! K&N’s 63-3073 provides increased performance while maintaining that “O/E” look with a rotationally molded high-density polyethylene tube.

K&N air intakes completely replace the restrictive factory air intake assembly with an aerodynamically engineered tube and an oversized air filter. K&N’s rotationally molded high-density polyethylene tubes offer the most flexibility in design and outstanding horsepower numbers. With a K&N performance air intake system, consumers can count on increased acceleration and horsepower whether winding along a lonely country road or passing cars on a highway.

This air intake system uses a uniquely shaped carbon fiber high-flow air filter (RP-5161).  This filter captures harmful particles, increases airflow, and also increases service life. This K&N air filter performs for up to 100,000 miles before service is required depending on driving conditions. The 63-3073 takes about 90 minutes or less to install, using simple hand tools, requires no cutting or drilling, and is covered by the K&N Million Mile Limited Warranty®.

K&N air intake system, part number 63-3073 installed in a 2008 Chevrolet Corvette with a 6.2 liter V8 engine

K&N 69-1017TTK air intake system for 2009 Honda Fit with a 1.5 liter engine

The 2009 Honda Fit was completely redesigned for 2009. It is a bit longer and wider than the 2008 model and has added interior space, sharper handling, enhanced seating functionality, and a more powerful engine.

K&N has designed a performance air intake system (69-1017TTK) in black for the 2009 Honda Fit with a 1.5 liter engine that is guaranteed to increase power.  K&N dynamometer tests show the 1.8 liter engine gained 4.53 horsepower at 6000 RPMs with this air intake kit.

The 69-1017TTK has lower restriction than the factory air box system. It draws air through a high flow washable and reusable chrome top K&N air filter (RC-9630) which is protected by a powder coated heat shield.

The heat shield directs incoming fresh air from the factory air inlet into the air filter and isolates the K&N air filter from the engine compartment for better performance. The heat shield assembly is installed into the engine bay using factory mounting points and attaches to the intake tube.

The 69-1017TTK integrates the mount from the vehicle’s mass air sensor. Remove the mass air sensor from your vehicle’s stock air box and install it into K&N’s less restrictive mandrel bent aluminum tube using the provided K&N hardware.

All the OE emissions devices are reused and the MAS placed in a location that works with the factory settings. The provided crankcase vent hose attaches to the aluminum intake tube. The 69-1017TTK can be easily installed in 90 minutes or less and is backed by the famous K&N Million Mile Limited Warranty.

K&N air intake system, part number 69-1017TTK installed in a 2009 Honda Fit with a 1.5 liter engine

K&N 57-9027 air intake system with air box cut out to see filter

K&N has developed an air intake system (57-9027) for the 2005 and 2006 Toyota Tundra Toyota Sequoia 4.7 liter V8 engine. K&N dynamometer tests show a 9.54 horsepower gain at 5472 RPM for this air intake kit.

Take a look at our 57-9027 features video to see dyno testing in progress.

K&N air intake systems are designed to smooth and straighten the airflow going into your engine while also reducing intake restriction and providing excellent filtration. The result is power that you can feel.
The K&N unique air filter (E-3034) is designed to incorporate the factory air box and carbon trap. This air intake system is street legal in all fifty states.

K&N air intakes are designed work with factory computer settings. Simply remove the factory air box assembly and replace it with the 57-9027. The mass air sensor adaptor is precision CNC machined for accurate mass air flow readings.

Installing a K&N performance air intake system can make your vehicle run better. Drivers can rely on extra horsepower when pulling a trailer, passing on a two lane road, or simply letting loose on the open road.

57-9027 installed

Installing the K&N 57-3034 on your vehicle takes 90 minutes or less and it is covered by K&N’s Million Mile Limited Warranty.  Take a look at our 57-3034 installation video to see all the steps involved.

Applications are as follows:
2006 TOYOTA TUNDRA 4.7L V8
2006 TOYOTA SEQUOIA 4.7L V8
2005 TOYOTA TUNDRA 4.7L V8
2005 TOYOTA SEQUOIA 4.7L V8

K&N's 63-3072 air intake system for the 2008 and 2009 Pontiac G8 with a 3.6 liter V6 engine

A few years back Pontiac decided to restore its reputation as GM’s High-Performance brand. Pontiac has seen much success with their line of G8 models. A mechanical twin of the highly successful Holden Commodore sedan, the G8 brings back the power and rear wheel drive once missing from Pontiac’s new car offerings. Entry-level G8 V6 models are capable of producing over 250 hp, which means the G8 rivals full size competitors from Chrysler as well as those in  Germany. Also helping to restore Pontiac’s performance heritage is K&N Air Intake System part 63-3072 for the 2008-09 G8 with a 3.6 liter V6 engine.

K&N’s Performance Air Intake System 63-3072 helps fire up an already impressive sport sedan with a nearly 11 horsepower increase at the rear wheels. K&N’s Research and Development Department tested a 2008 Pontiac G8 3.6L V6 on our in-house dynamometer. Results showed an increase across the RPM range with a dramatic peak horsepower gain of 10.68 horsepower @ 6,200 RPM!.

K&N intakes are designed to dramatically reduce intake restriction as they smooth and straighten airflow. This results in more power when you need it. With a K&N Performance Air Intake System, consumers can count on extra horsepower whether picking up the kids from school or winding along a mountain road.

This air intake system uses a conical shaped high-flow chrome-top air filter (RC-5138) and powder coated aluminum heat shield in place of the vehicle’s stock air box. The result is an air filter that captures harmful particles, flows air freely, and has a long service life.

63-3072 K&N air intake system installed on a 2008 Pontiac V6 with a 3.6 liter V6 engine

K&N's 69-6546TWR Performance Air Intake System for the 2008-09 Mitsubishi Lancer Evolution 2.0L Turbo L4

Mitsubishi’s Lancer Evolution, once a highly coveted Japanese Domestic Market only vehicle, graced North American shores in 2003. Since then the Evolution, or Evo as it is commonly called, has undergone two significant redesigns. Each generation Evo is designated by a Roman numeral. 2008 saw the debut of the 10th generation, or Evo X. Featuring a newly designed all aluminum 2.0L turbocharged engine, and Super All Wheel Control, the Evo X is capable of producing nearly 300 horsepower in stock trim. Always hungry for more power, K&N engineers took one look under the hood and decided that more could be done.

That’s exactly what K&N did with Performance Air Intake System 69-6546TWR. Much consideration was put into the design of part number 69-6546TWR for the 2008 and 2009 Mitsubishi Lancer Evolution with a 2.0 liter engine. Unique features include a powder coated aluminum upper intercooler and turbo inlet tubes replacing the stock pieces for improved air delivery. 69-6546TWR incorporates a unique heat shield, which retains the use of the factory fresh air scoop. The result of this hard work and enthusiasm for performance is an incredible 21 horsepower gain at the wheels for the 2008-09 Lancer Evolution.

Read More→

K&N's 63-3068 Performance Air Intake System for the 2006-2007 Cadillac CTS-V 6.0L V8

American made luxury automobiles, like Cadillac, once captivated the imagination of consumers around the globe. With the rise of the young urban professional, European, and later Japanese, luxury cars invaded the market. American luxury became thought of as a “grandfather’s” car. This unfavorable stereotype no longer holds true for Cadillac. Gone are the days of heavy, inefficient land yachts. Cadillac’s CTS-V helps to usher in this new era of American built luxury cars. The “V” moniker in the Cadillac line-up is intended as a direct contender to imported luxury such as BMW’s M series and Lexus’ F cars.

Performance Air Intake System 63-3068 stimulates an already incredible super sport sedan with a 17 horsepower increase at the rear wheels. K&N’s Research and Development Department tested a 2007 Cadillac CTS-V 6.0L V8 on our in-house dynamometer. Results showed an increase across the RPM range with a staggering peak horsepower gain of 17.09 horsepower @ 5,117 RPM! K&N’s 63-3068 provides increased performance while maintaining that “O/E” look with a rotationally molded high-density polyethylene tube.

K&N intakes are designed to dramatically reduce intake restriction as they smooth and straighten airflow. More air means more power and torque when you need it. With a K&N Performance Air Intake System, consumers can count on extra horsepower whether entertaining clients, or winding through the Santa Monica mountains.

This air intake system uses a conical shaped high-flow chrome-top air filter (RC-8049) and powder coated aluminum heat shield in place of the vehicle’s stock air box. The result is an air filter that captures harmful particles, flows more air, and increases service life. This K&N air filter performs for up to 100,000 miles before service is required depending on driving conditions. Improving the air path between the filter and the engine is the rotationally molded high-density polyethylene tube. It offers the most flexibility in design and outstanding horsepower numbers. 63-3068 takes about 90 minutes or less to install, using simple hand tools, requires no cutting or drilling, and is covered by K&N’s Million Mile Limited Warranty®.

K&N Air Intake System installed on 2007 Cadillac CTS-V 6.0L V8